We can provide you with thorough knowledge and modern products which we develop and manufacture ourselves. We offer professional advice, design of complete fall protection systems, a complete assortment of products, custo......We can provide you with thorough knowledge and modern products which we develop and manufacture ourselves. We offer professional advice, design of complete fall protection systems, a complete assortment of products, customer designed training programmers, overhauls and inspections, and above all else customer service and quality! Cresto offers a fall protection system which is equally well suited for those who occasionally use the system as it is for those who use the system in their daily work. Our design and technical solutions make it easy to use our products while they of course offer the saftey you require from personal protection equipment. For example, all our harnesses have fixed D-ring on the back which prevents the harness from ending up around the users neck in the case of a fall. All our products are approved according to the existing requirements and standards. There is a difference between fall protection and support equipment. Support equipments consists of products designed to provide support and prevent a fall. Included here are support belts, support lanyards, etc. (Standards EN 358, EN 813). Fall protection equipment is used when there exists a risk for a free-fall. The equipment should prevent a free-fall, and in the event of a fall catch the person so as to avoid injury. Included here are full body harnesses, fall arresters, runners/trolleys on stationary or flexible lines, etc (Standards EN361, EN354, EN353-1, EN353-2, EN355, EN360, EN362) According to EN 365:1992, fall protection equipment and support equipment should be inspected at least once every twelve months. The inspection should be carried out by a "competent person" who is certified by the products manufacturer. If the equip- ment is exposed to a lot of wear and tear, then it should be inspected more oten. Ask where you purchased your equipment for someone who can conduct an inspection. Each user is also responsible to checking the equipment before using it. If you are looking for a supplier of fall protection equipment who will help take responsibility fpr dangerous working situations, and someone you can have confidence in, then we will be your supplier and working partner. Our knowledge is your security.

We have produced and marketed ergonomic aids/auxiliary devices for professionals, mainly within the construction industry since 1978. Through years of cooperation with innovative building workers and companies, the trade...... We have produced and marketed ergonomic aids/auxiliary devices for professionals, mainly within the construction industry since 1978. Through years of cooperation with innovative building workers and companies, the trade mark Starke Arvid has grown strongly within the construction and contracting businesses. Our own development, construction, production and marketing have made us one of the strongest advancing companies, with many innovative ideas that still need to be developed. Starke Arvid are just now improving our ”old boys" so that they will perform even better and thereby suit future demands and requirements. We try continually to find new innovative solutions that will simplify the building process. We think in cycles from the manufacturing of materials for building and back to the recycling phase and a manufacturer’s responsibilities.

We have supported the global process industry with steel belt based solutions for more than 100 years. Todays product portfolio contains Steel Belts, Industrial Processing and Press Plates. Three units under the same umbr......We have supported the global process industry with steel belt based solutions for more than 100 years. Todays product portfolio contains Steel Belts, Industrial Processing and Press Plates. Three units under the same umbrella, Sandvik Process Systems. The common task for our departments is to continue supporting present and potential customers the best possible way.

We manufacture innovative pneumatic and hydraulic power tools on the basis of long tradition and great knowledge in quality, ergonomy and performance. We also offer agency products from leading business colleagues in Japa......We manufacture innovative pneumatic and hydraulic power tools on the basis of long tradition and great knowledge in quality, ergonomy and performance. We also offer agency products from leading business colleagues in Japan, a .o. Powertools is situated in Enköping, Sweden, in that part of the country where mining, metal treatment and mechanical development first emerged and in many cases became world dominant. We know power tools and would like you to give us the possibility to prove it in cooperation with you we present designs that will fulfil your wishes.

We supply laser based measurement and alignment systems for all types of industries and needs: Shaft alignment, sheave/pulley alignment and geometrical measurements of virtually every kind. Easy-Laser® reduces your mainte......We supply laser based measurement and alignment systems for all types of industries and needs: Shaft alignment, sheave/pulley alignment and geometrical measurements of virtually every kind. Easy-Laser® reduces your maintenance costs, energy consumption and minimizes unscheduled downtime within your operations. Great savings can be made, and your investment is usually repaid within just a few months. It is good to have Easy-Laser® to rely on. High product quality and a personal touch are givens. We have short delivery times, fast service and the best product warranty on the market. The measurement systems are also versatile and expandable, which makes them easy to adapt to your needs. Our aim with Easy-Laser® is to make sure that you always get the most comprehensive measurement system for your money!

Weightlifter of Olympic calibre The Simson Compact is a hydraulic powerpack that combines a number of unique properties. Low weight, compact dimensions and high capacity characterize all of our jacks. Quality and reliabil......Weightlifter of Olympic calibre The Simson Compact is a hydraulic powerpack that combines a number of unique properties. Low weight, compact dimensions and high capacity characterize all of our jacks. Quality and reliability are two further key attributes that have made the Simson widely known as an appliance at the pinnacle of Olympic calibre. Pocket-size 15-tonner It weighs a mere 3.7 kg and is our smallest jack. But it can still lift a hefty 15 tonnes. So it is a hydraulic lightweight in the heavy class. This also applies to the whole of our range of jacks. High capacity in a neat design and with a low weight. These qualities have made the Simson Compact an appliance thats widely appreciated by repair technicians and erectors around the world. Safety is built into the Simson For safety reasons, every jack is equipped with a safety valve located on the pump side and set to trip at 825 bar. The Simson Compact is designed with a factor of safety of 3 against overloading, and a factor of safety of 4 against failure.

What is now Ljungmann AS was founded in 1861 by Christian H. G. Olsen, “instrument maker and commission artist”. Telegraph apparatus, astronomical telescopes and a host of measuring instruments are just a few examples o......What is now Ljungmann AS was founded in 1861 by Christian H. G. Olsen, “instrument maker and commission artist”. Telegraph apparatus, astronomical telescopes and a host of measuring instruments are just a few examples of the ideas and products demonstrated by this Norwegian inventor. The fact is that Yonetani – together with giants such as Mazda Motor Corp. and Toyota Motor Corp. – was among the first to obtain a licence to use new software to produce tools for pressure die casting and coremaking Component material varies widely mostly aluminium, but also copper, brass, stainless steel, titanium and all sorts of synthetic materials. “Ordinary” steel is rarely seen in the company’s lathes and milling machines. The magnificent double cell generates revenue during the dark hours. A DMU 50 eVolution and a DMC 64 V Linear positioned at an angle to each other are served by a WorkMaster. "This year, we also equipped our high-speed milling machines with the GPS 240 pallet system," continues Motohiko Ifuku. "We started cautiously with a single machine but as the results were so good that, within a couple of months, we installed the system on all the machines."

Westermo was established in the early 70s in the small village of Västermo approx. 150km southwest from Stockholm in Sweden. Since then Westermo has developed into a company with subsidiaries in England, Germany, Fr......Westermo was established in the early 70s in the small village of Västermo approx. 150km southwest from Stockholm in Sweden. Since then Westermo has developed into a company with subsidiaries in England, Germany, France and partners in 30 countries around the world. Westermo Data Communications Ltd, the UK subsidiary, is based in Southampton and was established in 1995. The company has shown steady annual growth, providing sales and support to the UK and Eire. As well as the Westermo product range, Westermo are also the agents for Elpro radios and the Ontime ethernet switches in the UK. Today the Westermo brand name is synonymous with Industrial Data Communications. Our experience of the industrial market goes far beyond our own products. We know how to set up different PLC´s when you need to connect a modem or we can give you advice about cabling, shielding or topology when you are designing your system.

WhizCut offers a complete external and internal range of tool holders and carbide inserts specially developed for CNC Swiss automatic lathes. With this new precision tooling WhizCut will help You improve productivity and ......WhizCut offers a complete external and internal range of tool holders and carbide inserts specially developed for CNC Swiss automatic lathes. With this new precision tooling WhizCut will help You improve productivity and reduce interruptions in production in your Swiss lathe. WhizFix Tool holder System The WhizFix tool holder system for external turning uses a bent pin and a nut to index the insert. Indexing an insert is easy, accurate and quick. You can index or change the insert while the tool holder is in the machine even if there only is access from the back side of the tool holder. WhizIn Internal Cutting System The WhizIn tool holder for internal turning applications has the carbide boring bar mounted at an angle to achieve greater precision. By mounting the carbide boring bar at an angle we grind away less from the base of the insert which makes the boring bar more stable. Other benefits are less grinding time and grinding stress and that the coolant may go through the tool holder and spray directly on to the cutting zone. WhizCut Special features Versatile with 2 clamping systems Inserts for all standard applications Up to 20° positive cutting rake Fully ground edge Micro grain Carbide PVD coated carbide inserts Chip control Unique back turning insert Easy indexing of inserts in the machine without taking out the tool holder An internal tooling program with outstanding stability Wide range of internal boring bars Boring bar diameter starts at 1 mm Custom made external and internal inserts can be specially made to suit customer needs

Wide, comprehensive product range Bevent Rasch continually develops new products for the ventilation market. New regulations, new viewpoints on the importance of saving energy, and other industrial trends are absorbed and......Wide, comprehensive product range Bevent Rasch continually develops new products for the ventilation market. New regulations, new viewpoints on the importance of saving energy, and other industrial trends are absorbed and transformed to well-proven, functionally correct, and easy to install product innovations. Ordering When the ventilation contractor purchases products the consultation programme provides the main guidelines. Information on the product characteristics, high quality and preferential pricing, enable a high degree of ordering efficiency. We are expanding in Europe Swedish ventilation praxis is often on the cutting-edge, and Swedish manufactured ventilation products are in demand around Europe. Our international representatives see good sales potential for the products in several European countries, and we look forward to a rapid increase in order inputs from our export markets.